This 16 gallon per minute hydraulic pump is a must have for any log splitter application. Fits a wide range of applications, most commonly used on log splitters with a rated force less than 35 TON. This 2 stage gear pump allows for maximum speed without a loss of pressure.
What size hydraulic pump should I use for my log splitter?
If your log splitter has a 6-7 Horsepower engine, you should opt for a two-stage hydraulic pump (about 3000 PSI) with 11 GPM. To get more speed, the pump either needs more flow (GPM) or a smaller cylinder. Smaller cylinders don’t require more power but will produce less force.
How do you size a wood splitter pump?
If you are serious about making your own backyard log splitter, then you want to have, at a minimum, the following components to provide the right amount of force and power for basic splitting of averaged sized, seasoned logs: A 5 Horsepower engine. A two-stage hydraulic pump rated at a max of 3 gpm at 2,500 psi.
How do I know what size hydraulic pump I need?
1 HP is required for each 1 GPM at 1500 PSI or any multiple of 1500 such as 3 GPM at 500 PSI, 2 GPM at 750 PSI, 1/2 GPM at 3000 PSI, etc. Another handy rule-of-thumb is that it takes about 5% of the pump maximum rated HP to drive the pump when unloaded and pressure is very low.
How much hydraulic pressure does a log splitter take?
The most common size for log splitters is “4 x 24″, 4″ bore by 24″ stroke. With 2500 PSI from the pump it can exert over 31,000 lbs of push force. To compare, a 5″ bore cylinder can produce 49,000 lbs force with the same pump, over 1 1/2 times as much.
How many gpm hydraulic pump do I need?
Calculate your Hydraulic (Fluid Power) Horsepower
Rules-Of-Thumb: Horsepower for driving a pump: For every 1 HP of drive, the equivalent of 1 GPM @ 1500 PSI can be produced. Horsepower for idling a pump: To idle a pump when it is unloaded will require about 5% of its full rated horsepower.
What is 2 stage hydraulic pump?
Hydraulic two stage gear pumps from Grainger are suitable for presses, log splitters, clamping units, and compactors. They feature an automatic 2-speed operation. The first-stage pump unloads fully at 450 psi while the second stage operates up to 3000 psi.
How can I make my log splitter more powerful?
Log splitter Upgrades – YouTube
How can I make my log splitter faster?
Only way to speed up a splitter is to move more oil. Either get a bigger pump or speed up the existing pump.
How do you make a 4 way log splitter wedge?
New Homemade Bolt On 4 Way Wedge for Log Splitter – YouTube
How do I choose a hydraulic pump?
To select the right pump, follow the steps below: Select the cylinder trying not to exceed 80% of its nominal rating on both, load and stroke. Select the pump according to the oil volume and the number of cylinders in operation. NOTE: We must add 35 cm³ of oil per meter of hose we use.
How do I choose a hydraulic pump motor?
If you calculate 20 GPM @ 300 PSI with an assumed overall efficiency of 89%, you would probably select a 5 Hp electric motor. However, if you calculate the same 20 GPM @ 300 PSI with the actual overall efficiency of 50%, you would know that you should be using a 7.5 Hp motor.
How do you select a hydraulic pump?
CALCULATING PUMP PRESSURE AND RESERVOIR VOLUME
- Enter the load being lifted by the cylinder (in lbs.)
- Enter the piston diameter of your cylinder (in inches)
- Enter the number of cylinders lifting your load.
- Enter the cylinder travel length, or stroke (in inches)
- You will need a pump capable of generating at least.
What pressure do log splitters run at?
Log splitters are heavy, which is why they’re designed to roll. Both tires have to be inflated to 30 psi. Any higher pressure is dangerous, any lower and you’re not going very far. Lubricate the beam area with motor oil so the wedge can slide freely.
What is the psi limit for the hose on the log splitter?
Typical hoses are rated from 2000 , 2500 or 3000 PSI. Find the weakest link an then set your pressure accordingly. If you have the proper components to allow, I think you would find quite a difference in power going from 2000 to 2500 PSI.
Why is my wood splitter so slow?
A slow log splitter is often caused by issues with the power supply, hydraulics, ram, fan, pump or cylinder. Checking each element one-by-one can help you identify the cause of the problem. The speed of a log-splitter cycle ranges from 3-5 seconds up to 30 seconds, depending on age and type of log splitter.
How many GPM will a 1 hp pump?
Number of submersible well pump stages determine pump lift capacity
| Table of Submersible Pump Stages vs HP vs Total Dynamic Head vs. GPM Flow Rate Capacity | ||
|---|---|---|
| Water Pump HP | Nr. of Pump Stages | GPM Flow Rate Capacity |
| 1 HP | 8 | 4 – 40 GPM (varies by TDH) |
| 1 1/2 HP | 11 | 4 – 40 GPM (varies by TDH) |
| 2 HP | 14 | 4 – 42 GPM (varies by TDH) |
How do I calculate engine pump size?
Pump Hydraulic Power (ph) = (D x Q x H x9.
Pump Hydraulic Power (ph) = (1000 x 0.005 x 65 x9. 87)/1000 =3KW. Motor/ Pump Shaft Power (ps)= ph / pe = 3 / 80% = 4KW. Required Motor Size: ps / me =4 / 90% = 4.5 KW.
How do you calculate horsepower for a hydraulic pump?
Use this equation to help figure out what electric motor horsepower (HP) is required to drive a hydraulic pump. SImply take the gallons per minute (GPM) multiplied by the pump pressure PSI then divide that number by the result of 1,714 times efficiency (we used 85% effiencey in this case).
What are 3 types of hydraulic pumps?
There are typically three types of hydraulic pump constructions found in mobile hydraulic applications. These include gear, piston, and vane, however, there are also clutch pumps, dump pumps, and pumps for refuse vehicles such as dry valve pumps and Muncie Power Products’ Live PakTM.
How do you adjust a 2 stage log splitter pump?
How to Adjust a 2-Stage Pump
- Adjust the hydraulic gauge by locating the adjustment screw on the back of the gauge. Use a flathead screwdriver to turn the screw. …
- Adjust the pressure switch, located behind the hydraulic gauge, by using a wrench to loosen the lock-nut on the switch, then turning the adjusting screw.
How do you increase hydraulic pressure in a log splitter?
Twist the screw on the side of the pump clockwise with a flat blade screwdriver to increase pressure, according to the scale printed or embossed on the side. Turning the screw counterclockwise decreases pump pressure. Raise the guards on the sides and back of the splitter to the upright locked position.
What is the fastest hydraulic log splitter?
This Hyper Split Fast Cycle log splitter by Tool Tuff Direct is one of the fastest hydraulic log splitters on the market today thanks to their new cylinder technology. Powered by a Ducar 6.5HP horizontal shaft engine. This proven engine has been tested in cold weather and high elevations.
What determines the tonnage of a log splitter?
Choosing the right log splitter tonnage will depend upon a few factors: The size of the log measured across, or its diameter. Whether the wood is green or seasoned. The density of the wood, or its hardness.
How do I increase the cycle time on my wood splitter?
Increasing Log Splitter Return Stroke Speed
If your desire is simply to just increase the return stroke speed, you can just replace the hydraulic cylinder with one that has a larger push rod diameter. This decreases the volume of fluid between the rod and the bore so that less fluid is required to retract the cylinder.
What is a kinetic log splitter?
In place of hydraulic pump systems, kinetic splitters use massive flywheels to convert energy from a motor or engine into a burst of force. That force drives a moveable rack and push plate into a log and pushes the log against the splitting wedge, breaking the wood apart.
How do you calculate the cycle of a cylinder?
Calculating Cylinder Speed – YouTube
How do you make a firewood splitter?
Homemade Log splitter part 1 – YouTube
How do you split a log wedge?
Making Wood Wedge to Split Log – YouTube
How do you use a wood splitter wedge?
Splitting Wood Using Sledge &, Wedge – YouTube
What type of hydraulic pump is most efficient?
Traditional spur gear pumps average about 80% efficiency, meaning your 10 input horsepower will net you 8 hydraulic horsepower. Vane pumps reside in the middle ground between gear and piston pumps. They’re more efficient than gear pumps, but less so than piston pumps.
Which type of pump consists of two spur or helical gears?
Which type of pump consists of two spur or helical gears? Explanation: The external gear pump consists of two spur or helical gears, which are meshed with each other and mounted inside the casing.
What is the most efficient hydraulic pump?
When it comes to the optimum hydraulic motor, you should consider a radial piston motor or axial piston motor, which have about 95%and 90% efficiency, respectively. Not surprisingly, you will pay less for vane motors, gear and orbital motors, but they are consequently rated lower in terms of energy efficiency, as well.
Can I use a hydraulic pump as a motor?
Gear pump is not designed to provide torque its designed to provide flow, however if the torque of the pump and its pressure ratings are equal with the gear motor then it can be used as a hydraulic motor.
How do you size a hydraulic gear pump?
Determine Displacement of a Gear Pump by Measuring Gears/Housing
How do 2 stage pumps work?
A two-stage pump has two suction impellers operating side by side. The operator must decide if he wants volume or more pressure by selecting a switch on the pump panel. … The pump operator must be comfortable with a transfer valve and decide when to use volume versus pressure.
What oil should I use in my wood splitter?
What oil do I need for my log splitter? AW22 or 32 Hydraulic oil is recommended for the log splitter. Automatic transmission fluid can be substituted and should only be used instead of hydraulic oil when temperatures are below 32 degrees F.
How many horsepower is a log splitter?
A regular hydro splitter around 20-30 tons seem to have around 6.5hp gas engine. Get above ~30 tons and you typically get 9-11 hp range.