Excellent Air Plasma Cutter: The Cut-50 Plasma Cutter can easily cut up to 0.55”(14 mm) metal under maximum output with ultimate portability weighing only 21.56 lbs.
How thick can a 65 amp plasma cutter cut?
| Operating data | ||
|---|---|---|
| Capacity | Thickness | Cut speed |
| 1″(25 mm) | 10 ipm (250 mm/min) | |
| Severance | 1-1/4″ (32 mm) | 5 ipm (125 mm/min.) |
| Pierce | 5/8″ (16 mm) * |
How thick will a 60 amp plasma cutter cut?
The 60 amp max rating cuts steel up to 7/8-inch thick. At 20 amps output, this plasma cutter will cut as thin as 22 gauge sheet metal.
How thick can a 100 amp plasma cutter cut?
| Phase | Three Phase |
|---|---|
| Max Cutting Thickness | 10 mm, 15 mm, 20 mm, 25 mm, 30 mm |
| Condition | New |
| Brand | FIREWELD |
| Minimum Order Quantity | 1 |
How thick will a 45 amp plasma cutter cut?
This is the new digitally controlled 20-55 amps Plasma Cutter Machine with advanced inverter technology and high cutting performance. Designed for portable repair work and small business project use, the CUT-45M Air Plasma Cutter cuts a thickness of 2/5 in. with the max severance thickness at 3/4 in.
How thick can a hypertherm 45 cut?
The Powermax45® XP plasma cutter delivers increased cut capacity – up to 16 mm (5/8″) metal – as well as faster cut speeds, and automatic gas adjustment for quick, simple setup and operation.
How thick can a plasma cutter cut?
Plasma cutters are used to perform cutting and gouging operations, with the average hand-held system capable of cutting a maximum metal thickness of about 1 inch. Plasma typically requires a source for compressed air and a substantial amount of electrical power.
Do all plasma cutters need air compressor?
Plasma cutters need air pressure to cut in a two-stage process. … Therefore, all plasma cutters need an air compressor to generate enough air pressure for the task. If you buy a plasma cutter without a built-in source of air, you’ll need a separate air compressor.
Where are Hobart plasma cutters made?
Hobart machines are American-made in Appleton, Wisconsin. The Airforce 27i plasma cutter is also CSA Certified. This machine features an ergonomic torch design and 12-foot leads on both the torch and the ground lead. The Hobart Airforce 27i features a built-in regulator, air filter and water separator.
How does a plasma cutter work?
Plasma cutters work by sending an electric arc through a gas that is passing through a constricted opening. The gas can be shop air, nitrogen, argon, oxygen. etc. This elevates the temperature of the gas to the point that it enters a 4th state of matter.
How thick can a 40 amp plasma cutter cut?
Designed for portable repair work and small business project use, CUT-40 Plasma Cutter cuts a thickness of 1/2 in., and the max severance thickness is 3/4 in. Type: DC Air Plasma Cutter. Supply Power: 110-Volt/230-Volt/60Hz/1-Phase.
How thick can a 30 amp plasma cutter cut?
Designed for portable repair work and small business project use, CUT-30 Plasma Cutter cuts a thickness of 3/8 in., and the max severance thickness is 1/2 in., Specifications: Type: DC Air Plasma Cutter, Supply Power: 115V/230V/60Hz/1-Phase, Rated Input Current: AC-115V/30A &, AC-230V/15A, Cutter Current Range: AC-115V …
CONTINUE READING BELOW
Why do plasma cuts have little to no distortion?
Why do plasma cuts have little or no distortion? Because the high temperature allows for a higher travel rate which results in a lower heat input area. … Standoff distance, orifice diameter, power setting, travel speed, gas, electrode and nozzle tip, swirling of the plasma gas, water injection.
Are reboot plasma cutters any good?
We concluded that the Reboot Plasma Cutter 50Amps is the best buy for your money. The leads are a bit short, and it isn’t designed for industrial use. However, for anyone needing to do some cutting at home, this slices an excellent cut through 1/2″ plate and can sever 3/8″ material when necessary.