What is the frog on a wood plane?

J: frog , an adjustable iron wedge that holds the plane iron at the proper angle and allows it to be varied in depth relative to the sole. The frog is screwed down to the inside of the sole through two parallel slots and on many planes is only adjustable with a screwdriver when the plane iron is removed.

What is the frog on a hand planer?

Here are the functions of the plane frog: One: One of the frog’s primary function as a separate entity to the sole is to carry the lateral adjustment mechanism and the depth adjustment mechanism. See pic above. Two: The frog itself allows the closing and opening of the throat.

What are the parts of a wood plane?

Parts of Wood Plane:

  • #1. Lever Cap.
  • #2. Chip Breaker.
  • #3. Iron.
  • #4. Adjustment.
  • #5. Tote.
  • #6. Knob.
  • #7. Frog.
  • #8. Sole.

What is the bottom of a wood plane called?

Body – Whether made of cast iron, steel, aluminum, or wood, the body is the main frame of the plane to which all the other parts attach, and which rides across the wood surface to be planed. The top side is often referred to as the bed, and the bottom is called the sole.

What is frog adjustment screw?

An adjustment screw sits directly below the adjustment wheel at the rear aspect of the frog that facilitates changes to the throat opening (shown below).

Why is a plane frog called a frog?

Apparently Traut and his co-workers started calling the thing a frog because it is just behind the throat—and harkened back to the saying “I’ve got a frog in my throat.” Stanley didn’t start using the term publicly in their documents for many years.


What is a chip breaker on a plane?

This ‘chip-breaker’ is the cap made from plate steel locked beneath the wedge or the lever cap that flexes the two-component cutting assembly to reduce vibration by causing tension in the cutting iron and the cap iron and so prevent chatter. It neither causes the wood to chip nor prevents the wood from chipping.

How are wood planes numbered?

The numbers 1 to 8 simply refer to different lengths of plane with #1 being (very) short and #8 being pretty long. … Long planes such as the #8 shown above are good for making wood straight and true. The typical smoother and jointer planes are a #4 and #7 respectively.

What is wood chisel?

A chisel is a tool with a characteristically shaped cutting edge (such that wood chisels have lent part of their name to a particular grind) of blade on its end, for carving or cutting a hard material such as wood, stone, or metal by hand, struck with a mallet, or mechanical power.

What tool is used to hold the wood on the table?

Table saw

A cabinet table saw, equipped for cutting large pieces of sheet stock in the direction of the wood’s grain (also known as ripping)
Other names Sawbench
Classification Power tool
Manufacturer Delta, Crown, Yato, SawStop, Milwaukee, Skilsaw, Bosch, Makita, Ryobi, Black &amp, Decker/DeWalt, among others

What is a jack plane used for?

A jack plane is a general-purpose woodworking bench plane, used for dressing timber down to size in preparation for truing and/or edge jointing. It is usually the first plane used on rough stock, but for rougher work it can be preceded by the scrub plane.

What is a hand plane used for?

A hand plane is a tool for shaping wood using muscle power to force the cutting blade over the wood surface. Some rotary power planers are motorized power tools used for the same types of larger tasks, but are unsuitable for fine-scale planing, where a miniature hand plane is used.

What is a chisel used for?

chisel, cutting tool with a sharpened edge at the end of a metal blade, used—often by driving with a mallet or hammer—in dressing, shaping, or working a solid material such as wood, stone, or metal.

How do you adjust the frog on a wood plane?

How to Adjust the Frog on a Bench Plane | Paul Sellers – YouTube

When did Stanley Add a frog adjustment screw?

TYPE 10 Stanley 1907-1909

A frog adjustment screw, first offered on the Bed Rock planes, is now added. This is located below the frog, and engages a fork that is screwed to the frog.

What is a scrub plane used for?

A scrub plane is designed to quickly remove large quantities of wood. Based on the Stanley 40 1/2, the open throat and curved blade allow you to take deep cuts with ease. Our Scrub Plane can quickly thickness rough sawn boards or cut stock to width before following with a Jack or Smoothing Plane.

How do you adjust a plane’s mouth?

Adjusting a Bench Plane Mouth – YouTube

What is plane handle called?

joystick. noun. an upright handle that a pilot uses to control the direction of a plane.

What angle are plane irons?

The primary bevel for chisels and plane blades is normally 25 degrees (a time-tested angle). If you look at the blade diagram above its perfectly acceptable, from a sharpness perspective, to hone the primary bevel flat and hone the back of the blade flat and where these two meet you can achieve a sharp cutting edge.

Do wooden planes need chip breakers?

Why You Need a Chip Breaker

The plane iron of a hand plane acts like a wedge, and without a chip breaker installed it can split the wood ahead of the blade, following the direction of the grain. This causes tearout (chipout) and results in an uneven wood surface. Without a chip breaker, a hand plane can cause tearout.

Is chip breaker necessary?

Another job relegated to the chip breaker is that of blade advancement functionary. While it is stiffening the cutting edge and breaking chips, the breaker is integral to, and serves a vital role in the depth-of-cut system.

Where do you put a chip breaker?

Adjust the Chipbreaker

The chipbreaker on a bevel down plane should also be set so the distance from the blade edge is slightly more than the width of the shavings you intend to make. For smoothing most hardwoods, 1/32 inch is good, though you may want to set it at 1/64 inch for difficult woods prone to tearout.

Which is the first hand plane?

The low-angle block (left) and shoulder (right) planes make great first planes for the power-tool woodworker, cleaning up marks that motorized tools leave behind. If you want to replace some powered machining operations with hand-plane work, test the waters with a No. 5 jack plane (left) or a No. 4 smoother (right).

What is the most valuable Stanley plane?

Stanley No. 1 Bench Plane This slightly rusted No. 1 and original box sold on 4 May 2009 for $2,918. It was the most expensive Stanley Plane sold on eBay in 2009.

What Is a Number 4 plane used for?

The No. 4 smoothing plane is historically the most common size. It is an excellent balance of sole length and cutter width to be useful for typical furniture parts.

Are Irwin Marples chisels any good?

These are excellent chisels despite the opinions of internet forum snobs. They have the potential to perform wonderfully. Out of the box, these are very serviceable. But, if you want to get the most from them, they need to be flattened and properly sharpened.

What are the 3 types of chisels?

Types of Chisels

  • Mortise Chisel. This chisel is meant for making mortises or cutting holes in wood. …
  • tang chisel. The tang chisel has a point that goes into the handle of the chisel. …
  • Socket Chisel. The socket chisel has a wooden piece that goes into the socket of the chisel. …
  • Japanese vs. western chisels.

What are the holding tools?

Holding tools

  • HOLDING TOOLS.
  • A. Clamps are made of different sizes and appearance that are fitted to its purpose. …
  • Types of clamps and metal vises.
  • clamp is used for holding small parts both at the bench and at the machine. …
  • Combination Pliers /Mechanical Pliers.
  • Slip joint pliers.
  • Side Cutting Pliers.
  • Long Nose Pliers.

Can you saw without a clamp?

The Need for Clamps

Some cuts are impossible without clamps, however, either because you would have to put your hand in the path of the blade to keep the wood steady or you need both hands to hold the cutting tool.

What are the 3 work holding devices used in carpentry section?

Types of Lathe Chuck

  • Four Jaw Chuck.
  • Three Jaw Chuck.
  • Magnetic Chuck.
  • Collet Chuck.
  • Combination Chuck.
  • Air Chuck or Hydraulically Operated Chuck.
  • Drill Chuck.

How do you keep wood in place while cutting?

Two Ways to Hold Wood Without a Vise – YouTube

What is the longest bench plane?

The longest and heaviest of the bench planes, the No. 8 will flatten and true like no other. It is capable of precise joints and perfect flatness of large areas.

What is a Plough plane?

A grooving plane, plow plane, or plough plane is a plane used in woodworking to make grooves and (with some of the metal versions) small rabbets. They are traditionally used for drawer bottoms or rear walls.

What is the difference between a block plane and a bench plane?

Bench planes are used to flatten surfaces like a tabletop or the face of a board. Typically they have a longer blade than a block plane, which makes them ideal for heavy cuts. Block planes, on the other hand, are used for finer work like trimming end grain and fitting joints.

Are hand planers worth it?

The better tool for thicknessing stock is a dedicated benchtop planer (see photo, above). They don’t take up much storage space, even in a small shop, and they work great for reducing boards up to about 12- or 13-in. wide (depending on the planer) down to whatever thickness you need them to be.

Are hand planers any good?

An electric hand planer is a great tool to have for handymen, craftsmen, DIYers, and many more. They can make a difficult job easy, and free up time that is better spent on relaxing after a job well done. If you are still using an old-fashioned planer, it is definitely time to get your hands on a buzzer.

What is the difference between a jack plane and a smoothing plane?

Jack planes have toothed edges (or irons) that often teeth into the wood, whereas smoothing planes feature an iron with no sharp edges. This means that you can make smoother surfaces without leaving ugly tracks in your workpiece.

What is a claw hammer used for?

Claw and Framing Hammers

While these hammers all feature a round head for driving nails, the claw end is every bit as useful for prying, splitting wood, tearing drywall and other small demolition tasks. The claw is curved on a claw hammer, and straight on framing hammers. These hammers are best for: Woodworking.

How did cold chisel get their name?

They formed in Adelaide during September 1973 on the initiative of guitarist/singer Ian Moss. In the beginning, the band used a different name for every performance. After they used the name of the Don Walker song “Cold Chisel” for one particular performance, the name stuck.

What are paring chisels?

Traditionally used by cabinet- and pattern-makers for shaving thin slivers of wood. These paring chisels feature a long, flat, thin blade which tapers towards the cutting edge to give the finest of cuts when cleaning out grooves. Normally used for hand paring with one hand on the handle and the other controlling blade.

Are Stanley frogs interchangeable?

Stanley used parts to make planes and on,y new designs that rendered parts obsolete were changes with hard stops. Type 10 and later frogs are interchangeable.

How do you use a Stanley No 4 plane?

Initializing My New Stanley No. 4 Hand Plane – YouTube

How do you adjust a Stanley Bailey plane?

What is a Bailey Pattern Plane How to Adjust a Stanley – YouTube