Although expansion tanks can be installed on the hot side, we strongly recommend they be installed on the cold line, downstream of the shutoff valve.
Where should the expansion tank be installed?
An expansion tank is generally installed directly above the water heater by means of a tee-fitting installed in the cold water delivery pipe. The expansion tank is usually installed vertically, though it is acceptable to install it horizontally if it is necessary because of space limitations.
Does it matter which way an expansion tank is installed?
Expansion tanks can be installed in any direction. Whether oriented uprightly, horizontally, or even upside down, the expansion tank will function properly without any adverse effects. When putting an expansion in an abnormal position (specifically sideways or horizontally), make sure to support the tank.
Why is expansion tank on cold water side?
As water is heated the molecules expand the pressure in the water heater can get to be greater than the incoming water pressure allowing hot water to flow back into the cold water side increasing the pressure in the whole house. This can damage other plumbing fixtures.
On which side of the pump should an expansion tank be installed?
Location: The expansion tank should always be tied into the system on the suction side of the system pump, never on the discharge side of the pump. This is also called the point of no pressure change in the system.
Can expansion tank be installed outside?
An expansion tank, such as the one shown above, helps to absorb water pressure that results from thermal expansion. The tank can be installed anywhere in the cold-water line between the house’s main valve and water heater, or on the hot-water line within 3 ft. to 5 ft.
CONTINUE READING BELOW
Where does the expansion tank go in a hydronic heating system?
The tank should be located on the hot water return piping after the terminal units. It should end up close to the top of the return riser. It should be piped using the traditional rules, off the side of the pipe with a thermal loop.
Should an expansion tank be vertical or horizontal?
Do mount tank vertically with connection at top: It is also best to install diaphragm type expansion tanks vertically with the piping connection at the top. This reduces stress on the tank’s connection relative to horizontal mounting.
Can expansion tank be installed horizontal?
Can a water heater thermal expansion tank be installed sideways/horizontally? Most expansion tanks are designed to be installed vertically (stem up or stem down). You can install one sideways, but it will shorten the lifespan unless it is designed and specified by the manufacturer for horizontal installation.
Can a well pressure tank be installed on its side?
Answer, Yes it is a factor, the tanks are designed to sit air stem up or air stem down. Sitting a vertical tank horizontally puts more pressure on the lower parts of the bladder and can cause early failure.
How do I add pressure to my expansion tank?
Adjusting the Pre-Charge of a Thermal Expansion Tank – YouTube
Is it code to have an expansion tank on water heater?
California Plumbing Code Section 608.3 requires an expansion tank to be installed on the water heater when it is a closed system. A closed system is one that has a check valve, or backflow prevention device.
What pressure should an expansion vessel be set to?
Some important things to consider is the air pressure inside the expansion vessel. It rarely needs to be anything more than 1.5 bar in most domestic properties. Anything more and the water may not expand into the air at the required time and could risk the high pressure relief valve opening or worse.
How do you check pressure in an expansion tank?
Once you completely open the valve, you can measure and note the pressure. You can also check your expansion tank’s pre-charge pressure by knocking on the side of the tank with your knuckles to determine if it’s full of air or water. Pre-charge pressure that’s too low may be indicated when the tank is full of water.
Should you drain expansion tank?
Draining the expansion tank should be done periodically, usually once or twice a year. We recommend doing this maintenance before the cool season so you don’t have to work with hot water and risk getting burned. Turn off the boiler and close the water supply valve.
Will an expansion tank increase water pressure?
The expansion tank contains air, which is highly compressible. Expanding water from the water heater can flow into the expansion tank, where the air compresses, making room for the increased volume of water. Water pressure in the system doesn’t increase significantly.
How close should expansion tank be to water heater?
The items which should be installed in sequence in the cold water line are (1) the EXPANSION TANK must be installed at least 18 inches away from the cold water inlet fitting on the water heater, (2) the PRESSURE GAUGE, and (3) the PRESSURE REDUCING VALVE, if required, see Figure 1. 3.
Will an expansion tank stop water hammer?
An expansion tank contains a rubber bladder and compressed air that absorb the energy wave as water flows through a pipe. As this device cushions the shock wave, it prevents water hammer.
Where should an expansion tank be located on boiler system?
A boiler expansion tank is located at the top of the main water tank of the water boiler. When water is heated, it expands. Therefore, the tank is there to provide space so that water can escape when it is heated.
How do you install an expansion tank on a water heater?
How to Install Water Heater Expansion Tank
- Step 1: Disconnect the Water and Power Supply. …
- Step 2: Bring Out Expansion Tank and Accessories. …
- Step 3: Confirm the Water Supply Line for Cold Water. …
- Step 4: Install the Expansion Tank. …
- Step 5: Attach the Heater Tank. …
- Step 6: Restore the Water and Power Supply to the Heater.
Do expansion vessels have to be vertical?
They should be mounted vertically to cut down on debris becoming trapped, fitted with an isolation valve and be designed to minimise the amount of water held inside the vessel and stimulate the flow of water.
What does a white expansion vessel do?
How Does an Expansion Vessel Work? The purpose of an expansion vessel is to help prevent overpressure situations with an unvented cylinder. As water is heated, it expands. The air within the expansion vessel compresses and absorbs additional pressure to help ensure that your water heater operates in a stable way.
Can you put an expansion vessel on its side?
2 Answers. In general, the tank can be installed vertically above or below the plumbing, or horizontally. Typically, the tank is only required to be supported when installed in the horizontal position. Most smaller tanks are designed to be supported by the plumbing, when installed in the vertical orientation.
Can a reverse osmosis tank lay on its side?
The tank works fine standing up or laying down on its side. So if you lack headroom or don’t have enough space near the RO system, you can lay the tank down or put it elsewhere within 20-30 ft horizontal, and 10-15 ft vertical from the RO, and it will work fine.
How much pressure should a reverse osmosis tank have?
Reverse Osmosis tanks should have pressure of 7 to 8 psi without any water in the tank. To check your pressure, locate the Schrader valve, typically covered by a blue plastic cap, on the side of the tank near the bottom.
What pressure should my boiler expansion tank be?
For most installations, the expansion tank pre-charge setting should be the same as the boiler’s cold pressure setting. That’s why the manufacturer ships the expansion tank pre-charged to 12 psi. That’s the same default feed pressure found on hydronic boiler water feeders.
How much air should I put in my expansion tank?
Expansion tanks are pre-charged with a 40 PSI air charge. If the inlet water pressure is higher than 40 PSI,the expansion tank’s air pressure must be adjusted to match that pressure but must not be higher than 80 PSI.
Can expansion tank cause low water pressure?
Before installing an expansion tank, measure the tank’s air pressure charge. When taken from the box, the air pressure in the expansion tanks will likely be lower than your home’s water pressure.
Do you need an expansion tank with a backflow preventer?
If a home does not have some form of backflow preventer this pressure is put back into the municipal system. The bottom line is if your home has well water or a back flow preventer you need an expansion tank for safety (according to current Ohio Plumbing Code).
Why do I need an expansion tank on my hot water heater?
Because water will expand when heated, the excess pressure inside the water heater tank needs to be released. … The expansion tank is designed to handle the thermal expansion of water as it heats up in the water heater, preventing excessive water pressure.
How do hot water expansion tanks work?
Expansion tanks work by equalizing pressure throughout the system. … As hot water enters the heating system, the pressure in the system increases. As pressure increases, the diaphragm in the expansion tank is pushed down. This compresses the air in the tank, creating more space for excess water to enter.
Should an expansion vessel have water in it?
There should be water in the water side of the expansion vessel. It is actually preferable that all air is removed from the water side.
How much air pressure should be in water pressure tank?
Your well tank’s pressure should be set at 2 psi below the pressure switch’s cut-on point. This differs depending on your tank’s pressure settings. Most well tanks come set at 30/50. The cut-on pressure for the well pump is 30 psi, so the pressure of the tank should have a pressure of 28 psi.
What is the difference between a pressure tank and an expansion tank?
The most significant difference between expansion and pressure tanks is their functionality. An expansion tank handles water expansion and provides protection for water valves and heaters. On the other side, the pressure tank lengthens the lifespan of the pump.
How do you bleed an expansion tank?
3 Answers
- Turn off the valve that auto-fills the system from your cold water line.
- If you have one, open a valve or bleeder on the top of your expansion tank. …
- Open a drain valve and drain a suitable amount of water.
- Close drain valve and re-open valve you closed in step 1.
How do I know if my expansion tank has failed?
Check your relief valve on the water heater. It’s located on the side of the water heater with a tube that goes to the floor. If the relief valve is dripping, this could indicate your expansion tank has failed.
Why does my expansion tank keep overflowing?
The most common cause of an overflowing header tank is a fault with the float mechanism, which may not be rising to the correct level and therefore not stopping the supply of water to the tank. This causes it to overflow through the outlet pipe (causing that cascade of water!).
How does expansion tank work on central heating?
How does an expansion vessel work? When heated, water molecules vibrate and move, causing the water to expand in size. This means that water inside the boiler will expand upwards and, if left unchecked, increase the pressure in the system to dangerous levels.