What size flapper do i need?

How do I know if toilet flapper is 2 inch or 3 inch?

Look at the flush valve drain opening at the bottom of your tank.

1. If the opening looks about the size of a baseball or orange, you need a 2″ flapper.
2. If the opening looks about the size of a softball or grapefruit, you need a 3″ flapper.

How do I know what size flapper to buy?

What toilet flapper size do I need? – YouTube

How do you measure a toilet bowl flapper?

An easy reference for determining your toilet’s flapper size is to look at the flush valve drain opening at the bottom of your tank. STEP 2: If your flapper is the size of a baseball or an orange, your toilet requires a two inch flapper.

Are toilet flappers universal?

Are all toilet flappers universal? No. There are universal designs like the Fluidmaster flappers that replace most other flappers and there are specialty flappers for specific flushing systems.

Is korky or fluidmaster better?

The Korky gasket material is nice and spongy, yet sturdy – the quality feels better to me than the Fluidmaster. As with replacement flush valves, there’s more than one size of gasket available. 2 inch is by far the most common, with some newer toilets using 3 inch valves.
…

Fluidmaster	Model 6102	2″
Korky	Model 481BP	3″

What do the numbers on a toilet flapper mean?

The 502 flapper can be turned like a dial and has numbers on it that range from minimum to a maximum setting. Turning the flapper to a lower number forces the flapper to close sooner for a shorter flush and setting it to a higher number will allow it to stay open longer for a longer flush.

How do you replace a Kohler 1.6 gallon toilet flapper?

Fix a Running Toilet – How to Replace a Toilet Flapper – YouTube

How do I stop my toilet from running intermittently?

If the toilet keeps running or runs intermittently, you’re not getting a good seal. Try a different flapper if the toilet won’t stop running. If you just can’t find a flapper that seals, consider replacing the entire toilet overflow tube/flapper. On most toilets (two-piece), this means removing the tank.

Are all toilet fill valves the same size?

Toilet flush valves come in different sizes ranging from 2 to 4 inches, depending on the toilet design. If you are thinking of buying a new toilet, pay attention to the type of flush valve it has. In most cases, larger valves move water faster, resulting in a better flush.

How do you know if the flapper needs to be replaced?

A constantly running toilet is one sign of a worn-out flapper. To test your flapper’s performance, put a few drops of food coloring into the tank water. Don’t flush the toilet. If after 30 minutes you find colored water in the toilet bowl, replace the flapper yourself or call a plumber to do the job for you.

What size is a toilet fill valve?

The standard size of a flush valve is 2 inches. This size is what you’ll likely find at a home improvement store and should work on most toilets, including low-flow and older models with larger tanks.

How do I choose a toilet fill valve?

How to Pick a Toilet Fill Valve and Flap – YouTube

How do you replace a old toilet flapper?

How to Replace Your Toilet Flapper | Tips from Mr. Rooter Plumbing

Do I need a float on my toilet flapper?

Get a Flapper with a Chain Float

A chain float helps the flapper stay open a bit longer, allowing more water to enter the bowl for a better flush. You can adjust the float up or down on the chain to fine-tune how long the flapper remains open. Get a stronger flush—and a lower water bill.

How do I replace the flapper in my toilet?

How to Replace a Toilet Flapper Valve – Plumbing Tips from Roto-Rooter

Is Fluidmaster made by Kohler?

Fortunately, yes. A commonly known aspect in plumbing is that Fluidmaster actually makes the parts for Kohler toilets. Sometimes they are rebranded and built to the specs for Kohler’s requests, but the innards are the same!

Does Fluidmaster work on Kohler?

The Fluidmaster K-400H-5002 PerforMAX High Performance Toilet Fill Valve and Specialty Flush Valve Seals Repair Kit for Kohler and American Standard eliminates the guesswork when repairing your specialty flush valve toilet.

What is the best toilet flapper seal?

The Fluidmaster 502P21 PerforMax is one of the best adjustable models in the market and takes the top spot. Similarly, the Fluidmaster 5403 Toilet Flapper is a long-lasting option, followed by the Korky 54BP Toilet Tank Flapper for its super-tight sealing.

How do I add weight to my toilet flapper?

If you want to add weight to the flapper, you have to remove the chain from the lever and put the chain through the half-inch nut. The nut won’t get in the way of closure if the chain is used.

Why does toilet run after replacing flapper?

The most likely cause is a leaking flush valve. Usually such a leak is around the mouth of the flush valve where the flapper is supposed to make a good seal. Lift the flapper and run your finger around the edge of the opening where water spills through the flush valve and into the bowl.

Why does the toilet flapper closing too soon?

There are a few common reasons. Typically, the toilet flapper closes quickly because the water level is too low, or you tend to half-flush the toilet. Other reasons include a clogged drainage hole, waterlogged float, and a damaged flapper.

Does korky work with Kohler?

Kohler® Toilet Flapper &amp, Replacement Parts

Korky designs many types of replacement toilet parts to fit Kohler® toilets.

Why does my new Kohler toilet keep running?

This issue is common during new toilet installation because turning the water supply on and off can loosen sediment within the water lines. Replace the fill valve if the toilet is still constantly running after flushing the fill valve. The part number of the fill valve will vary based on the toilet model number.

Can you replace a canister flush valve with a flapper?

The canister style flush valve seal is easily replaced. Turn off the water supply to the toilet. Turn the guide, located in the center of the canister, a 1/4 turn counterclockwise, the white refill tube connects into the top of the guide (Fig.

Why does toilet run every 5 minutes?

A toilet that cuts on and off by itself, or runs intermittently, has a problem that plumbers call a “phantom flush.” The cause is a very slow leak from the tank into the bowl. This problem is almost certainly caused by a bad flapper or flapper seat.

Why does my American Standard toilet keep running?

Among the most common causes for a running toilet is overflow water leaking down into the bowl from the tank via the overflow tube. This happens when there’s too much water in the tank. You can adjust the water level by adjusting the height of the float.

Why does my toilet sound like water is running?

Running noises occur when water leaks out of the tank and into the bowl, and then the tank re-fills with water. These noises should cease as soon as the tank is finished filling. Running noises when no one flushes could mean a variety of things: The valve in the tank allows water to escape into the bowl.

What is the standard toilet supply line size?

Typically they are 3/8” in diameter, but toilet supply line size can vary in length, usually anywhere from 9” to 20”. Measure for accuracy to ensure you are buying a part that will match your installation.

What is a 1920 flapper?

Flappers of the 1920s were young women known for their energetic freedom, embracing a lifestyle viewed by many at the time as outrageous, immoral or downright dangerous. Now considered the first generation of independent American women, flappers pushed barriers in economic, political and sexual freedom for women.

How often should you replace your toilet flapper?

The average toilet flapper lasts about 4 to 5 years. It is important that you replace your toilet flapper when needed to prevent damaging leaks.

Can you put Vaseline on a toilet flapper?

One easy, but temporary fix to make rubber toilet parts supple again is vaseline. The toilet must be drained and dried for this to work. Then, vaseline can be rubbed on the flapper and it’s connecting washer until they become soft. The toilet should be filled and checked again.

Are toilet inlet valves universal?

Most are quite interchangeable and can fit the standard tank openings on any toilet, but do pay attention to sizes, especially the length of the valve stem. Many modern toilets have a rather small tank, and you’ll need to make sure the stem on the new fill valve is short enough.

What is a 2 flush valve?

2 inch and 3 inch Flush Valves are valves that flush using a flapper valve to release the water. The designation 2 inch and 3 inch describe the drain opening along with the corresponding size of the flapper that covers the drain opening.

How many types of toilet flappers are there?

3. Types: There are two types of flappers, Adjustable Flappers and Non-Adjustable Flappers, and these flappers are designed for specific flushing capacities of toilets.

How much does a toilet flapper cost?

Cost of Replacement Parts

Part	Price	DIY Project Time
Fill Valve	$8 – $30	1 – 2 hours
Shut Off Valve	$5 – $35	1 – 2 hours
Bowl Flush Valve	$20 – $30	½ – 2 hours
Flapper	$5 – $10	20 – 30 minutes

Why do I have to hold down the toilet handle?

If You Have to Hold Toilet Handle Down to Flush the Toilet

When there is too much slack in the lifting chain that connects the toilet flapper valve to the flush lever, the chain will not be able to lift the flapper high enough to allow the full amount of water to flow down through the flush valve.

How long should flapper stay open?

The bottom line is that the flapper has to stay open long enough for the toilet to flush completely. If you have a contemporary low-flow toilet, the flapper can rise almost to the vertical position, it will then stay open long enough for the level of the water in the tank to fall to the rim of the siphon tube.

How can I make my toilet flapper last longer?

Fix for toilet flapper closing too early so toilet won’t flush properly