To calculate the wrench size needed, you must first measure your bolt. Take the diameter of the bolt, and multiply by 1.5. This calculation and conversion factor is valid for either metric or standard bolt sizes. The resulting number will be the size of the wrench you need to adjust the bolt properly.
What size wrench is most common?
Most common are the 1/4-inch, 3/8-inch and ½-inch ratchet drivers, but ¾-inch and 1-inch sets are available for heavy-duty work.
What size wrench fits a fitting?
Hex) Standard to 3/4 in. Fittings.
What is better 6 point or 12 point?
Answer: It’s true that 12-point sockets are fine for most lightweight repairs, but heavy wrenching calls for a six-point socket. A six-point socket is much less likely to slip off a stubborn fastener or round over the corners. Here’s why: (1) Six-point sockets have thicker walls, so they’re less likely to flew.
What wrench is smaller than 516?
Metric / Standard Wrench Conversion Chart
| Bolt Diameter | Metric | Standard |
|---|---|---|
| 3/16″ | 10mm | 3/8″ |
| 1/4″ | 11mm | 7/16″ |
| 5/16″ | 13mm | 1/2″ |
| 3/8″ | 14mm | 9/16″ |
What size is an4?
For example: a 3/8″ standard hose equals -6 AN.
…
Russell Performance Technical Support.
CONTINUE READING BELOW
| AN Size | Metal Tube O.D. | Thread Size |
|---|---|---|
| -3 AN | 3/16″ | 3/8″ – 24 SAE |
| -4 AN | 1/4″ | 7/16″ – 20 SAE |
| -5 AN | 5/16″ | 1/2″ – 20 SAE |
| -6 AN | 3/8″ | 9/16″ – 18 SAE |
How do I know my fitting size?
You can always identify AN fittings based on the male thread size (outside diameter). These sizes are constant regardless of brand, hose type, or fitting configuration. If your fitting has a convex 37 degree flare at the end, the threads will tell you the AN size (and vice-versa).
What size wrench fits a garden hose?
usually an 8″ wrench will work.
Why are impact sockets black?
Impact sockets are typically black. This is because the surface is carbonized in order for it to harden. Ensuring that the surface is hard allows the sockets to absorb sudden torque changes i.e. “impact” a lot better.
What is the most common socket drive size?
Drive Size
- ½-inch drive size sockets are for high-torque applications like automotive wheel replacement and when you are using a breaker bar. …
- ⅜-inch drive size sockets are the most common and most available. …
- ¼-inch drive size sockets are ideal when you are in tight spaces or when you are working with recessed nuts.
Can I use a 12 point socket on a 6-point nut?
A 12-point end is a double-hexagon (sometimes called “double-hex”)—it has 12 points, or vertices, evenly spaced at 30 degree increments around a circle. This geometry will also fit on a 6-point fastener. Your tool will work best when it fits precisely onto the fastener.
Is 3/8 and 10mm the same?
9mm = almost 3/8 inch. 10mm = just over 3/8 inch. 11mm = almost 7/16 inch. 12mm = almost 15/32 inch (= almost 1/2 inch)
Will a 9/16 fit a 14mm?
But thats no biggie ~ to answer your question, 9/16 SAE is actually 14.3 Metric, but it is the closest SAE size that will fit a 14mm metric head.
What is a 10mm socket equivalent to?
SAE to Metric Conversion Chart
| SAE | Metric | Inch |
|---|---|---|
| 9mm | 0.354 | |
| 3/8″ | 0.375 | |
| 10mm | 0.394 | |
| 13/32″ | 0.406 |
What thread is AN8?
It’s Not Rocket Science
| AN Size | Metal Tube O.D. | Thread Size |
|---|---|---|
| 6 | 3/8″ | 9/16-18 SAE |
| 8 | 1/2″ | 3/4-16 SAE |
| 10 | 5/8″ | 7/8-14 SAE |
| 12 | 3/4″ | 1-1/16-12 SAE |
What size thread is AN4?
AN4 bolts have a 1/4-28 UNF thread. All sizes of AN4 bolts have a 0.469 inch thread length (except AN4-3A, which has 0.406 inch thread length).
What size is AN8?
Plumbing Basics – AN Fittings &, Hoses
| AN Size | Hose i.d. – Tube o.d. | SAE Thread Size |
|---|---|---|
| –6 | 3/8 in. | 9/16 in.-18 |
| -8 | 1/2 in. | 3/4 in.-16 |
| -10 | 5/8 in. | 7/8 in.-14 |
| -12 | 3/4 in. | 1 1/16 in.-12 |
How do you size an AN fitting?
AN sizes range from -2 (dash two) to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in 1/16″ increments. Therefore, a -8 AN size would be equal to 1/2″ OD tube (8 × 1/16 = 1/2).
How do you find a line size?
The outside diameter is from outside edge to outside edge across the pipe. To find it, measure around the circumference of the pipe with flexible measuring tape. Divide the circumference by pi, or about 3.14159.
What is 6 an fitting?
In bolts the number refers to the diameter of the bolt whereas in a fitting it refers to the OD of the tube and thereby have different threads. For example, AN6 bolt has a 3⁄8-24 thread whereas an -6 AN fitting has a 9⁄16-18 thread.
What size is a standard outdoor faucet?
Hose bibs are outdoor faucets, usually mounted onto the side of your house. Most often they have a threaded outlet to which you can attach a garden hose or backflow device. The outlet will be one of two widths: 1/2 inch or 3/4 inch. These are two most common widths of water pipes as well.
What size is normal garden hose?
Hose Diameter
Because standard household piping is typically ½ inch in diameter, most homeowners only need a standard garden hose size of ½ inch in diameter. A 5/8 inch diameter garden hose size may also work for you, but you’ll likely be adding unnecessary weight with this size hose.
How do you measure a garden hose fitting?
Remove the paper tube, using care not to let the tube slip open as you remove it from the hose. Secure the tube with additional tape if necessary. Measure the distance across the opening in the paper tube with a ruler. This measurement equals the diameter of the inside of your garden hose.
Is it OK to use impact sockets with a ratchet?
Can I use an impact socket on a hand ratchet? You can absolutely use an impact socket on a hand tool ratchet, a breaker bar or a torque wrench without damaging the tool or placing yourself at risk. New impact sockets are designed with a shoulder that is stepped down to a parallel neck.
Can you use regular sockets with a torque wrench?
Absolutely as long as you have the right size socket for the size of the drive on the end of the torque wrench… You sure can, but don’t use them with a pneumatic system. A lot depends on how high you have the wrench set to twist the bolt or nut. If it exceeds the capacity of the socket it will break.
Can I use standard sockets on an impact wrench?
Impact sockets can be used safely on a hand tool, however you should never use a regular hand tool socket on an impact wrench as this can be extremely dangerous. A regular socket is likely to shatter when used on power tools due to their thinner wall design and the material they’re made from.
Whats bigger 3/8 or 1/2 socket?
3/8 is the smaller version ratchet, and 1/2 is the larger version ratchet.
Do sockets come in metric and standard sizing?
You can check the size of sockets in the metric as well as in the SAE system.
What are the 3 common ratchet drive sizes?
Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets.
Why do 12 point sockets exist?
The additional points make these sockets easier to connect with the heads of fasteners. This is ideal if you are trying to work on a fastener that is hard to see or you cannot see at all. 12 point sockets are also great for use in tight spaces as they allow you to connect to a fastener at more angles.
What are 8 point sockets used for?
What is an 8 point socket used for? Our range of 8 point sockets are perfect for use on our range of Pyramid Head Door Screws, Lag Bolts and Square Headed Machine Bolts. 8 point sockets take away the need for the use of a shifter and will stop you rounding off the head of a square bolt.
Can a 12 point socket be used on hex head bolt?
Both 6-point and 12-point sockets can be fitted on hex nuts, the primary differences being convenience and torque. The more points a socket has, the more points of contact available. Compared with the 6-point socket, a 12-point socket has twice as many points, so it can more easily slide onto a hex nut.
Can I use a 3/8 instead of 10mm?
3/8th of an inch is the closest SAE wrench size to 10mm.
What size is 7mm?
3/8th of an inch is the closest SAE wrench size to 10mm.
Is there a 10mm socket?
In fact, the 10mm socket is one of the most commonly used metric size sockets of all. It’s no secret that the majority of parts under the hood and in the car require a 10mm. The applications may vary from car to car, but the 10mm is absolutely vital to complete a project.
Is M14 the same as 9 16?
The size of a metric screw or bolt is specified as diameter, pitch and length, in millimeters (millimeters is abbreviated “mm”). For nuts, size will appear as diameter and pitch.
…
Table 3.
| Metric | Closest Inch |
|---|---|
| M8-1.25 | 5/16-18 (Smaller) |
| M10-1.5 | 3/8-16 (Smaller) |
| M12-1.75 | 1/2-13 (Larger) |
| M14-2.0 | 9/16-12 (Larger) |
What is the equivalent to a 14mm socket?
Standard / Metric Wrench Conversion Chart
| Bolt Diameter | Standard | Metric |
|---|---|---|
| 5/16″ | 1/2″ | 13mm |
| 3/8″ | 9/16″ | 14mm |
| 7/16″ | 5/8″ | 16mm |
| 1/2″ | 3/4″ | 19mm |
What is 12 mm in fractions?
Standard / Metric Wrench Conversion Chart
| Bolt Diameter | Standard | Metric |
|---|---|---|
| 5/16″ | 1/2″ | 13mm |
| 3/8″ | 9/16″ | 14mm |
| 7/16″ | 5/8″ | 16mm |
| 1/2″ | 3/4″ | 19mm |
What size bolt uses a 10mm wrench?
Size Chart
| Bolt size | Size | Tolerance |
|---|---|---|
| M6 | 10mm | 10.04 |
| M7 | 11mm | 11.04 |
| 1/4″UNF | 7/16″ | 11.15 |
| 3/16″BSW | 11.34 |
What size bolt uses 10mm socket?
The standard 6mm cap screw has a 10mm head.
What size wrench fits a M10 nut?
Any ISO M10 nut normally requires a 17mm spanner or socket.
What thread is AN3?
AN3 bolts have a 10-32 thread with a 3/16″ shank diameter. All sizes of AN3 bolts have a 0.406 inch thread length, regardless of grip length.
What size is 10AN?
The Good News
| Male Thread Size | AN Size* | Equivalent Tube Size (Nominal OD) |
|---|---|---|
| 7/16-20 | 4AN | 1/4″ |
| 9/16-18 | 6AN | 3/8″ |
| 3/4-16 | 8AN | 1/2″ |
| 7/8-14 | 10AN | 5/8″ |
Is JIC and SAE the same?
JIC fittings are dimensionally identical to AN (Army-Navy) fittings, but are produced to less exacting tolerances and are generally less costly. SAE 45-degree flare fittings are similar in appearance, but are not interchangeable, though dash sizes 2, 3, 4, 5, 8, 10, 14, and 16 share the same thread size.