USG Durock™ Brand Tile Backer Screws for wood framing come in three lengths: 1-1/4″, 1-5/8″ and 2-1/4″. USG Durock™ tile backer screws for steel framing can be used with steel framing where steel thickness is from 14- to 20-gauge, they come in two lengths: 1-1/4″ and 1-5/8″.
What sizes does cement board come in?
Sizes. Cement board is most commonly sold in 3 x 5-foot sheets and in thicknesses ranging from 1/4 inch to 5/8 inch. A 3 x 5 panel of 1/4-inch cement board weighs about 30 pounds, a 1/2-inch sheet, 36 to 44 pounds. Larger, 4 x 8-foot panels are also available, but their weight makes them hard to manage for DIYers.
What size durock goes on the floor?
1/4″ USG Durock® cement board is an ideal substrate for floor and countertop ceramic tile installations. The 1/4″ thickness helps eliminate transition trim when abutting carpet or wood flooring and minimize level variations with other finish materials.
How much does a sheet of durock cost?
DUROCK 1/2 x 4′ x 8′ Cement Board at Menards
| Everyday Low Price | $32.39 |
|---|---|
| 11% Mail-In Rebate Good Through 3/5/22 | $3.56 |
What is the difference between durock and Hardibacker?
Durock is too abrasive and can damage vinyl, porcelain, and enamel. HardieBacker does not contain any course materials, so it is the preferable choice. It has a warranty that extends over the use of vinyl tile applications.
What size is cement backer board?
Cement board, technically called cementitious backer unit (CBU), is manufactured under different brand names. The standard size sheet is 3 x 5 ft. and 1/2 in. thick, weighs 45 to 60 lbs.
CONTINUE READING BELOW
Can I just screw down cement board?
Screw and Joints
Do not use drywall screws as they are not recommended to be used to hold the backer board in place. All of your backer board pieces should be cut before they are placed on the floor.
Do I need thinset under durock?
However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used.
Do you tape durock seams?
For tile backer boards such as Durock, Wonderboard, Hardiebacker, Permabase, and others the seams between the board need to be treated with 2-inch alkali-resistant mesh tape.
How far apart are screws in durock?
Fasten panels to subfloor while the adhesive is wet with 32 mm (1-1/4″) CGC Durock Wood Screws or 38 mm (1-1/2″) hot-dipped galvanized roofing nails spaced 203 mm (8″) o.c. in both directions.
How much does a 3×5 sheet of durock weight?
2.4 lbs./sq.
How do you cut durock?
To cut DUROCK Brand Cement Board, mark desired size on the board with a rule and pencil. Score both sides and edges with a utility knife through the glass-fiber mesh, and snap the board to size. Smooth cut edges with wood rasp. Cutting with a circular saw with a car- bide-tipped blade is an alterna- tive.
Can you Durock 1/4 walls?
1/4″ hardibacker alone is an unsuitable substrate for shower wall tile. If it were attached to properly waterproofed drywall, plywood, or plaster it would be fine. Think about it, one wayward elbow, knee, or hip bump and you may get flexion which would cause the grout (or tile) to crack.
What is the thinnest backer board for tile?
It does suggest that 1/4-inch cement backerboards are generally useful for the underlayment of tiled floors.
What is the best backer board for a shower?
Cement board is a good, reliable backer board that works well on both floors and walls. Keep in mind that most tile setters err on the side of caution and brush a waterproofing membrane on top of cement board when it is in wet areas like showers or tub surrounds.
What thinset do I use for cement board?
An unmodified thinset (Masterblend) is fine between the Hardi and the subfloor. The reason for the layer of thinset between the cement board and the subfloor is to fill the voids/gaps between the two. It’ll keep the cement board from moving up and down.
What do you do with a gap between tub and cement board?
Technically, after the tile is installed over the backer board that gap between it and the tub ledge should be filled with an ASTM C920 sealant (caulking e.g. silicone). Although some say you should have weep holes along this gap so any water behind can weep out into the tub.
Is 1/4 inch cement board on the floor?
Floors. Both 1/4- and1/2-inch cement board are appropriate for floors. To install cement board on floors, cement board manufacturers mandate a 5/8-inch plywood subfloor or OSB underlayment. They also require a 3/4-inch subfloor where tile size exceeds 12 inches.
Do you put thinset under cement board?
Use thin-set mortar when installing cement backer board. Thin-set dries slowly, allowing you to fix and readjust backer board sheets as needed. The ingredients in thin-set mortar ingredients are cement, fine sand and a water retaining agent.
Do you have to tape cement board before tiling?
If you are going to tile over the cement board, you should tape the seams. This should not be that difficult. Pack in thinset, lay on the tape, and flat-knife to get it set in. In the corners, use a corner knife.
Is Ditra better than cement board?
Schulter Ditra or Cement Board (Hardibacker, Durock, Wonderboard, etc.) is typically used as a tile substrate because it is durable, water resistant, and does not expand, contract, or warp when exposed to moisture. Schluter Ditra is superior to cement board in all categories except price and durability.
What’s the best way to cut cement board?
First, you’ll want to choose a scoring tool. A carbide-tipped scoring knife is recommended, but you can also use a utility knife or shears. Never use a high-speed grinder to cut cement board indoors, since this can create a dust hazard.
What put under durock?
Subfloor should be minimum 5/8″ APA span-rated plywood or OSB with an Exposure 1 classification or better. Minimum 3/4″ APA span- rated plywood or OSB with an Exposure 1 classification or better. Cover base with USG Durock™ Brand Tile Membrane, 15 lb. felt or 4-mil polyethylene and attach with 1/4″ galvanized staples.
Is mortar the same as Thinset?
The word “thinset” is sometimes used interchangeably with “mortar,” because it’s a type of modified mortar made specifically for tile. Thinset is made of sand, water, and cement, and can also contain additives for increased bonding, water resistance, and flexibility.
Can you use drywall mud on durock?
Things You’ll Need
Durock Cement Boards are a type of drywall reinforced with cement for a harder surface. This type of wall material can be finished just like ordinary drywall, using joint tape and joint compound.
Can I use drywall mesh tape for cement board?
Apply Mesh Tape
Paper tape simply won’t hold up on cement board. Although paper tape generally leads to a cleaner finish on drywall, you can still achieve a smooth look if you use mesh tape on a drywall/cement board joint. Use this self-adhesive joint tape where cement board and drywall meet.
Can you use drywall mud on cement board?
When using drywall compound over cement board, it is recommended, but not required, to use a faster setting-type joint compound (45 or 90 min), than typical joint compound. Make sure to follow manufacturer guidelines for the products used to finish the non-tiled area.
How do you attach a subfloor to a durock?
Part 2 – How To Install Durock On The Floor – Complete Bathroom Remodel
Does durock need to be waterproofed?
Should USG Durock® Brand Cement Board Panels be waterproofed in wet area use? Water does not affect USG Durock® Brand Cement Board, however, TCNA guidelines recommend the use of a waterproof membrane in wet areas.
How many screws do I need for a 3×5 cement board?
We recommend referring to the cement board manufacturers guidelines for screw pattern. In floor applications, screws should be placed every 8″”. You will use approximately 55 screws per 3′ x 5′ cement board and 91 screws per 4′ x 8′ cement board. In ceiling applications, screws should be placed every 6″”.
Can I use cement board around a fireplace?
However, using fiber cement board like Hardieboard is acceptable in locations including the mantel and fireplace surround.
Is cement board the same as Durock?
Durock and Hardiebacker are two different brands of cement backer boards used in rooms that are susceptible to moisture buildup. While both of these brands offer products that are highly raved about by users, each brand does have their own features that set them apart from each other.
How thick should cement board be for shower walls?
The minimum recommended thickness for the shower wall is 1/2″ because like some of the other boards, they become far too flexible at thicknesses below 1/2″.
Can you score and snap durock?
This durable material resists moisture and mold, making it ideal for bathrooms and high-humidity areas. It’s also stronger than plywood, making it useful for floor, wall and countertop installations. You can cut by scoring and snapping or by using a circular saw for straight cuts and hole saws or jigsaws for cutouts.
Can you cut cement board with a Sawzall?
A: You can cut cement backer board with a circular saw or grinder equipped with an abrasive or diamond blade. A reciprocating saw with an abrasive blade will also do the trick, and so will a backerboard scoring knife, which works like a standard razor knife but with a carbide cutting edge.
Can you cut cement board with a utility knife?
You can cut a cement board by hand if you mark the cutting portion with a pencil and use a utility knife to cut through. A utility knife is the best option for cutting cement boards, second only to a scoring knife.